Please be sure to ask any questions prior to ordering (we attempt to describe in detail but if we missed anything or you wish clarification, please feel free & be sure to ask us prior to ordering). There are many details, so please read full listing before ordering. SPECIAL NOTE: Photo's may show zippers in the VINYL WINDOWS but our standard listings DO NOT INCLUDE these zippers.
If you wish any vinyl window to open using zippers, it can be added. It is also mentioned in our PHOTO DESCRIPTION.
Soft Full length DOORS + REAR Panel. Clear + 1 Pc + Vented LEXAN Windshield (Level 2). For your existing poly top. Zforce 500, 800, 800EX, 1000. SPECIAL NOTE REGARDING 2018+ ZForce: The newer CF Moto ZForce has a quarter door.
This full length door will not work with the factory hard lower quarter door. If you were to remove this quarter door then our full length door will work for your UTV. Again, this listing is a full length door NOT compatible with Factory hard lower Quarter Doors. Refer to our other listings for Short length doors if Factory Suicide Doors are installed on your UTV. REAR Panel with Vinyl Window.
Both full length DOORS with Vinyl Windows. NOTE: Shorter Upper Doors available if you have Mfg Lower Hard Doors installed. Level 2, Lexan Windshield, Clear color with Quick Connect Clamps + Dual Vents. EXCLUDES: Top (assumes you have a poly top).LEVEL 2 Lexan Windshield Includes. Our Premium, Level 2 Lexan Windshields are 1 piece Windshield made from standard Lexan 9034 with flex trim along the hood line and sides. We use Quick Connect Clamps to secure to the roll cage. They include Dual Vents(vents can be omitted if you wish). This same UTV goes under the following names in other countries.
These MODULAR Doors can be fully removed using the zipper (great for full removal during the warmer months). The door can also unzip, then roll back and be secured in an open position with the velcro tabs/snaps sewn into the enclosure (great for fall days when it is cold when you start out but then warms up in the afternoon). Lexan Windshield includes our Dual Vent design. The dual vents run across the bottom in front of the driver and another in front of the passenger.They open and close by sliding the panel. These Enclosures for the CF Moto ZForce is 100% Fully Modular. Every piece is made to work with the other.
PROUDLY Made in the USA. COLOR:- Choice of 2 Standard Colors. Onyx Black or Mossy Oak Break-Up. (National Guard Woodland Camo color is no longer available). Approximately 8 - 25 Days.
Busy Season run September - February. May be longer during busiest months November-January. Absolutely Top of the Line Product.Great Shelter from All Weather (Rain/Snow/Sun/Wind). Photo 1: Shows Doors & Rear Panel Enclosure. Photo 2: Shows Doors & Rear Panel NOTE: Top shown in photo not included. This listing assumes you have a Poly Top. Photo 3: Shows Doors & Rear Panel.
(NOTE: Top shown in photo not included, this listing assumes you have a Poly Top). Photo 4: Lexan Windshield with Dual vents and standard clamps.
NOTE: You will receive the Quick Connect Clamps shown in photo 5. Photo 5: Close up of Quick Connect Clamps.
Photo 6-9: Quality of materials and workmanship on all of our enclosure styles. Photo 10: Standard enclosure colors available. (NOTE: Natl Guard / Woodland Camo no longer available). Photo 11: Shows the Doors & Rear combo enclosure, along with lexan windshield when combined with your existing poly top (Poly Top not included). Photo 12: Shows Doors & Rear combo with your existing poly top (Poly Top not included).
SPECIAL NOTE: Photo's may show zippers in the VINYL WINDOWS but this is not include in this standard listing. If you wish vinyl windows to open using zippers, it can be added. The Doors & Rear Enclosure with a Lexan Windshield will fit all CF Motor ZForce 500, 800, 800EX, 1000.
The enclosure is available in solid colors of Heavy Duty top gun marine canvas or in Camo patterns made of heavy duty Cordura nylon. The TOP GUN marine canvas fabric is water repellent, tear resistant, puncture resistant, and UV resistant.
Black and Beige are in-stock colors but additional colors are available upon request. The 1000 denier Cordura nylon Camo patterns have a polyurethane backing for water resistance. This is the same high quality fabric found in the big name backpacks. This rugged fabric is made from Invista's acclaimed, patented high performance polymer, designed for superior strength and abrasion resistance.
The WINDSHIELD is 1/4 Lexan so it will not bow at high speed and door & back windows are made of 30 gauge Aqua-View smoked vinyl allowing for an uninhibited view and total clarity. The enclosure adheres to the cab with heavy duty Velcro hook & loop along with 2 Poly-Pro webbing that is manufactured for industrial use. The Poly-Pro webbing has a tensile strength of 2,000 pounds.As with all enclosures, the full cab enclosure is hand measured and manufactured in the USA for superior fit and quality. The product kit includes the adhesive Velcro as well as installation and care instructions. This enclosure is BRAND NEW. Made to Order for YOU!
It will fit all models and years shown above. Two (2) Standard Colors: Black, National Guard Woodland Camo, Mossy Oak Break-Up. SOLID Marine canvas is water repellent, tear resistant, puncture resistant, mildew & UV resistant with less than 1% stretch or shrinkage. If you are looking for a quality enclosure for your UTV, look no further.
TOP OF THE LINE ENCLOSURE. This enclosure isn't your run of the mill, inexpensively made enclosure from. Pacific Eagle Enclosures are proudly made in the. Using only the highest grade and time proven materials.
The material withstands being stretched over a boat for years on end enduring the buffeting wind, blowing rain, and harsh sun. This marine canvas fabric is the Top Gun brand. It is a durable, high count woven polyester that is coated on both sides with a specially formulated polymeric coating that will not harden, crack or peel after outdoor exposure or extreme temperatures.The coating adds UV, Mildew & Water Resistance but can still breath so it will not trap excess moisture. The stitching is a continuous multi-filament polyester yarn. Google it and you will find out just how durable this material is. Its stretch-ability is limited to 1% and this helps it to retain the nice tight fit you would expect from a high quality enclosure. Please check out the pictures.
We show you close up shots that others shy away from. SPECIAL NOTE: Photo's may show zippers in the VINYL WINDOWS but our standard listing DO NOT INCLUDE these zippers. You can see the large industrial sized zippers and the clarity of view through your Lexan windshield & the heavy Vinyl door windows & more. Take a close look at the windows on others, they can look pretty crinkled.
When you initially take the few extra minutes to install the enclosure properly, you will love the tight fit that makes it stand out among others. The doors roll back and strap to the rear for that open air feel. You won't have to remove doors & store them away under your seat. The Lexan Windshield is made of 1/4" Lexan which is much stronger than the 3/16" versions that will bow at high speeds with fast sport UTV's.
We also use quick connect clamps with our Lexan screens. These make installation a BREEZE! After the clamps are on your roll bar, you never have to remove them to take your windshield off. Just loosen the knob bolts to remove the Windshield.
You are getting the best of both worlds here. Our Lexan Windshields includes a 2 strip of rubber edging along the bottom and both sides. This edging protects the Windshield from hitting the roll bar when running hard and the rubber edging stops that cold. Even though one person can do it, two people are recommended to take advantage of its ability to fit tight.The long, heavy 2 wide strips of hook & loop fasteners (Velcro) hold the enclosure tight in place. This kit comes with full instructions. A full hand tailored, custom fitting, absolutely top of the line enclosure. You won't be disappointed. OPTIONS AVAILABLE but NOT INCLUDED in this listing: May add 1-2 days to production time.
NOTE: Option 1 not available when ordering the short length soft doors that work with installed factory hard lower doors. OPTION 3: Add Zippers to the Rear vinyl window so window opens addl. Just unzip the zippers on each side, roll up the vinyl, and secure in open position with tabs included. OPTION 20 (on Doors only): Install 2 grommets to the lower door edge on each side of a 2 seat UTV, so you can bungee under your UTV from driver door to passenger door to secure while hauling. OPTION 21: ZIPPERS in 2 Door Vinyl Windows (2 door windows in front, driver/passenger).Allows vinyl windows to open. Not available in shorter Upper Doors. Door can be completely removed. Made to Highest Standards Hand Tailored for Precision Fit. Using Top of Line, Heavy Duty Marine Grade Materials. Stay True long lasting colors. Water Resistant / Mildew Resistant / UV Resistant / Tear & Puncture Resistant. Stretch & Shrinkage less than 1%. Large, Easy-To-Use YKK Zippers on Doors for unmatched Crosswise Strength in the Industry. All YKK Zippers work in extreme temperatures down to 50 degrees below zero. 30 gauge Aqua View Vinyl Windows- rear & doors. Lexan Windshield is 1/4 thick, available in clear. We have hauled our Lexan Windshield on UTV's going 60 miles per hour with ZERO bowing! Doors Unzip & Roll back to be secured safely with Velcro. Velcro rated from 0 to 120 degrees F. Easy To Install; Includes Self-Adhesive Velcro plus Installation & Care Instructions. Vents may be omitted if you wish.
Let us know at time of sale. Feel free to view our different levels of Hard Lexan Windshields and add to any of our individual or combo soft enclosures such as; Soft Top, Soft Doors, Soft Doors & Rear. At any time, the Mfg Design Department reserves the right to make changes to the enclosure style and/or materials from the listing description which improves its design and use. Majority of buyers install the enclosure with ease, however, there are a few buyers who prefer to have their dealer install. The enclosure itself is made for your year/make/model of UTV.Due to the fact that the ROPS and/or accessories on the UTV can vary, such as hard windshield and/or poly top, there is no one fit all situation regarding the attachment points of the windshield and/or poly top to the ROPS. Thus, the webbing of our soft enclosure will need to be cut to go around any of these attachment points. This is an easy process to perform and in the instructions.
Feel free to request a copy of the instructions. This applies mostly to styles that work with an existing hard windshield, poly top, or hard back panel such as Soft DOOR Kit, Soft Doors + Rear Panel combo, or Soft Back Panel styles of enclosures. Our soft enclosure will not fit over a Poly Top. If you wish to continue using a Poly Top, it will need to be mounted over our soft enclosure. Be sure to view our other enclosure styles.If your UTV is modified from the stock/standard mfg. Please be sure to specify the YEAR, MAKE & MODEL of your unit and your choice of enclosure COLOR (t he Year can be important because the fit can vary from year to year). Please be sure to specify the YEAR, MAKE & MODEL of your unit and your choice of enclosure COLOR. You are responsible to ask any and all questions prior to ordering. Your order confirmation (as well as the listing description) states what is included and excluded.
Exception - This does not included if the product sent is defective or the wrong item. In this case a photo is required for verification.Please read the listing to determine if you ordered the correct item. In this case a photo is required for verification of defect or wrong item. Then we will expedite a replacement. The photographs are of the actual item(s) for sale (not pasted or copied from elsewhere) unless stated in the listing as a Stock Photo. We attempt to check our emails on a regular basis, however, please allow 24 to 48 hours for a reply. We do not watch our e-mails 24 hours / 7 days per week. Any discrepancies from the listing must be reported to us within 24-48 hours of receipt of package. Please inspect goods upon receipt.
1- We will leave Feedback for all Buyers after they receive & inspect the merchandise and leave us feedback. We have implemented this policy to encourage Buyers to leave feedback (sadly, many buyers never get around to leaving feedback). 1- We will consider all REASONABLE Offers. 2- For your consideration when submitting an offer to us, we do not consider a discount of 50% or more off the listed price as Reasonable.We can only offer MEDIA. On certain items (books, cd, dvd, ect). Other than the name change, everything else is the same. Correction as of 04/01/2020 to. OUTSIDE CONTINENTAL USA, INTERNATIONAL SALES. NOTE: The enclosure itself is made specifically for your year/make/model of UTV.
This applies mostly to styles that works with an existing hard windshield, poly top, or hard back panel such as Soft DOOR Kit, Soft Doors + Rear Panel combo, or Soft Back Panel styles of enclosures. If this listing ABOVE states. What 2 states are not part of the continental US? There are no longer exemptions for lower valued items.Due to a rise in raw materials, effective November 07, 2021 there will be a price increase. Mfg facility has held off doing this for over a year. Those listings not updated by 11/07/2021, maybe pulled and not be viewable for a few days until the prices can be updated. Best wishes for a happy and safe holiday season!
NOTE: This applies more to SOFT DOORS, the DOOR & REAR combo, and BACK PANEL enclosure styles. Enclosures are attached to the roll bars, frame members, and/or body at various points using Velcro with self adhesive backing (placement will be different for each make/model). These pre-cut Adhesive Hook & Loop strips are applied to the various attachment points (roll bar, frame, and/or body) and will remain there if you decide to remove the enclosure during the warmer months. Most owners elect to leave the enclosures on during the warmer months and if they include doors, they run with them secured in the open position.
Some owners remove the enclosure completely and elect to leave the Velcro attached to the UTV for easy attachment the next winter. However, we have a small group who remove the Velcro from the roll bars, frame, and/or body completely when they remove the enclosure during the warmer months. The Velcro can be removed and the surface cleaned with a remover like Goof-Off. For these individuals, we sell a replacement adhesive Velcro kit. NOTE: This applies mostly to styles that work with an existing hard windshield, poly top, or hard back panel such as Soft DOOR Kit, Soft Doors + Rear Panel combo, or Soft Back Panel styles of enclosures.
This is an easy process to perform. Install enclosure first and be sure you are satisfied with the fit. Once satisified, cut to go around the brackets and seal the raw edge with a match or lighter to seal (have a damp rag handy just in case). Option 20 Install Grommets in lower edge of both Doors, to secure enclosure while hauling (bungie under UTV from driver side to passenger side).
Respect, Kindness and Polite Language is Required. If you bully, if you are rude or use Vulgar Language you will be blocked.
We shouldn't have to post this on our listings. Buyers are required to assist in locating lost package. Check all doors, garage and other buildings on your property to see if driver left package in a different location. Check with other household members to see if they received package and set aside without telling you. Check with your closest neighbors to see if delivered to them in error.
INDUSTRIAL ZIPPER MAINTENANCE: (Applies to Soft Marine Canvas enclosures only). If you reside in cold weather areas or extremely dirty areas, you will need the following for good performance of your zippers. All other areas, a good rinsing off with a water hose is advised after riding to remove dirt and keep zipper clean. #1 - YKK Zippy Cool Cleaning Fluid & Lubricating Stick, The Complete Zipper Care System (amazon.#2 - If caught without your Zippy Cool Stick, a Good old fashioned PARAFFIN WAX can be used. This item is in the category "eBay Motors\Parts & Accessories\ATV, Side-by-Side & UTV Parts & Accessories\Other ATV, Side-by-Side & UTV Parts & Accessories". The seller is "usa_made_utv_enclosures" and is located in this country: US. This item can be shipped worldwide.